ZShack is now an authorized Nistune dealer! We can handle all your Nistune needs at reasonable prices! Contact us for more information.

ZSHACK L.E.D.BULB KIT INSTRUCTIONS FOR MANUAL A/C CONTROLS

ZShack L.E.D.interior light installation instructions for manual A/C pod

 

The following is a list of the bulb sizes and where they go.
194— is for the instrument gauges. Requires 4.
74 fits map light, floor lights, ashtray light, cigarette lighter light, and key ring light.
3022 is the larger overhead cabin light
Neo 4 fits the headlight pod
Neo 3 fits the auto A/C pod
Neo 5 fits fits A/C pod

       

 
**WARNING**
All L.E.D. bulbs are directional. After you install them, plug the pod/cluster back in and turn the lights on to see if they all work. If not then remove non working bulb and rotate it 180°. Then re-install it and check again.
 
Remove gauge cluster. Bulbs circled in red are your illumination bulbs. Remove them, pull the old glass bulb out of the socket and install a 194 LED bulb into the socket. Then re-install socket into cluster. Test to make sure they all work. If not remove and rotate 180° and try again.
*** THERE ARE SOME EARLY YEARS THAT HAVE A DIFFERENT CLUSTER. IT USES 6 194 BULBS INSTEAD OF 4. IF YOU HAVE ONE OF THESE CLUSTERS, CONTACT US TO PURCHASE THE 2 ADDITIONAL BULBS NEEDED. UNFORTUNATELY THERE IS NO WAY TO KNOW WHICH MODELS HAD THIS 6 BULB CLUSTER STYLE UNTIL YOU OPEN YOUR DASH UP***
 

Remove manual A/C pod. Bulbs circled in red are your illumination bulbs.Remove them, install 4 Neo3 bulbs into the red locations. Test to make sure they all work. If not remove and rotate 180° and try again.

 

 
Remove headlight pod. Bulbs circled in red are your illumination bulbs. Remove them, install five NEO4 bulbs into the red locations. Test to make sure they all work. If not remove and rotate 180° and try again.
 
For dome light, carefully remove plastic lens by squeezing cover with fingers and pulling down at the same time. A small screwdriver or prying object may be needed. Replace the bulb by moving one of the metal holders away from the bulb while pulling down on the bulb. Replace with the white 3022 bulb.
 
For floor lights, look up under the dash for the light, remove the bulb from the side of the light. Remove the bulb from the socket and replace with one 74 led. Be careful when installing the led as you can damage it on the side of the housing causing it to not work.
 
For the key ring, remove the steering column plastics by first removing the upholstered part under the column to gain access to the screws for the column cover. On the ignition switch, there will be a small 74 light. Remove the old one and install a 74 led. Test and rotate if needed
 
For the ash tray and cigarette lighter lights, you must remove the radio/vent cover. There are 2 screws at the top behind covers and two screws behind the center bar cover. Remove them and gently pull it out. There are two clips
holding it in at the bottom. Next remove the 2 screws at the bottom holding the center console in place. Then remove the ash tray and remove the screw
underneath it. Next, lift up at the front of the center console and pull it towards the front of the car, look underneath it for the ash try bulb and the cigarette lighter ring bulb. They are both 74’s. Replace them and check that they work before reassembly.
For the map lights, remove them by gently prying down on the assembly with your hand or a prying tool. Unplug the harness and remove the screw circled in red. Carefully lift up on the wires and rotate the bulb holder over to gain access to them. Remove the glass bulbs and be careful as they break easy. Some pliers may be needed here. Install the white 74 in it’s place and plug the harness back in to test that they work before reassembling them. If not, remove and reinstall the bulb half a turn to get the right polarity.